Category Archives: fish

Art – Fish, Fish, and more Fish

Standard

In an effort to get caught up, I’m posting three different projects for this one.  Whew!

The first set is from my (last year’s) 3rd/4th graders:  Jellyfish.  First, they drew out their jellyfish very lightly, and then covered it in glue.  While the glue was still wet, they dripped watercolors and let it bleed.  Once the glue was dry, they added the watercolor background and used saran wrap to make it fractal.

This next set was created by my (then) 5th/6th graders.  We were practicing analogous colors.

The final set is from my (then) 7th/8th graders.  The challenge was to have at least one partially behind another, and at least one partially off the page.  I found some free coloring pages and printed them off for the kids to use and swap out.  They were able to trace whichever fishes they liked.  Then, they used oil pastels to make the fishes hyper-colorful.  Finally, they used watercolor to fill in any remaining fish parts as well as the background water.

Advertisements

Level 1 Art – Water Bottle Fishes

Standard

Yes, “fishes” is correct:  they’re different species.  😉

To start, you’ll need the following for each student:  1 disposable water bottle, 1 12-inch dowel rod, 1 4 x 4 wooden block.

You will also need:  scissors (or an exacto knife), masking tape, scrap cardboard, a drill (with a bit the size of your dowel rod), newspaper, flour, water, a hand-mixer, mixing bowl, cheap toilet paper, joint compound, vegetable oil, Elmer’s Glue-All (NOT school glue), modge podge, sponge brushes, tissue paper, large google-eyes, Aileen’s Tacky Glue, and sequins.

First things, first.  Remove the outer wrapping, lid, and ring from the water bottle.  Drill a hole in your wooden block and push one end of the dowel rod into it.  If it’s loose, add a little glue-all to it to help it stay put.  Using your scissors (or exacto knife), cut a SMALL slit on the side of the water bottle.  Push the other end of the dowel rod all the way into the bottle.  If it’s loose, use a piece of masking tape to secure it.

Cut out fish parts from the cardboard, like the fins and tail.  Tape those to the water bottle.  Rip SMALL pieces (about 2-3 inches) of newspaper, and set them aside.

WP_001176

Here you can see the skeletal structure.

In a mixing bowl, put about a cup of flour, and add enough water to where it becomes the consistency of pancake batter.  Dip a piece of newspaper into the batter and pull it through your index and middle fingers to wipe it off.  Press it to the water bottle, and smooth out any wrinkles.  Once the water bottle and cardboard pieces are completely covered (make sure to look under it!), let it dry.  Add another layer of paper mache.

WP_001179

This is the first layer of newspaper on the fish. See the dowel rod? When we first started the project, I used bamboo skewers, not even thinking about the weight of the sculpture. Duh! Anyway, after getting real dowel rods, having them cut down to thirds, and re-drilling the hold in the wooden block, all was well in the world of Mrs. Darby’s art class.

To create the paper mache clay, remove the toilet paper from the roll, and soak it in a bowl of warm water.  Squeeze the water out of it, and pull it apart in very small chunks into a mixing bowl.  Add 3/4 cup of Elmer’s Glue-All, 1 cup of joint compound, 2 tablespoons of vegetable oil, and a 1/2 cup of flour.  Mix on low for about 20 seconds, then mix on high for about 30 seconds.

WP_001233

Here is the big bucket o’ paper mache clay, ready to go!

Once the fish is dry, smear on the paper mache clay in a VERY THIN layer, smoothing it out as you go.  I made sure there were tubs of warm water at each table for when the kids were done.  I didn’t want to pour that down the sink.  Let the fish dry.

WP_001234

Abby puts on a thin layer of paper mache clay. This helps to fill any gaps missed and to smooth out any weird spots. Notice the new, thicker, stronger dowel rod?

You’re finally ready for the colorful part!  Cut small pieces of tissue paper and adhere with modge podge (I made ours by thinning white school glue with water).  Let dry.

When you're ready to add color, saturate the area with modge podge with a sponge brush.  Then add a piece of tissue paper and cover the area with modge podge to seal it.

When you’re ready to add color, saturate the area with modge podge with a sponge brush. Then add a piece of tissue paper and cover the area with modge podge to seal it.

This one’s ready for the next step:  Embellishment!

All the tissue paper is on!  Now to add the details...

All the tissue paper is on! Now to add the details…

Add the google-eyes and layer the sequins like scales in some areas.  Done!  🙂

Schooled in Love:  Water Bottle Fish

This project took us about 6 class periods to finish.